From f9ad937f537df92bf3119686eee97db7b7176674 Mon Sep 17 00:00:00 2001 From: paul Date: Fri, 21 Oct 2005 00:45:17 +0000 Subject: 2005-10-21 Paul Jakma * (general) OSPF fast, sub-second hello and 1s dead-interval support. A warning fix. Millisec support for ospf_timer_dump. Change auto-cost ref-bandwidth to add a comment to write out of config, rather than printing annoying messages to vty on startup. * ospf_dump.c: (ospf_timer_dump) Print out milliseconds too. Callers typically specify a length of 9, so most see millisecs unless they specify the additional length. * ospf_interface.h: (struct ospf_interface) new interface param, fast_hello. * ospf_interface.c: (ospf_if_table_lookup) add brackets, gcc warning fix. (ospf_new_if_params) Initialise fast_hello param. (ospf_free_if_params) Check whether fast_hello is configured. (ospf_if_new_hook) set fast_hello to default. * ospf_ism.h: Wrap OSPF_ISM_TIMER_ON inside do {} while (0) to prevent funny side-effects from its if statement when this macro is used conditionally by other macros. (OSPF_ISM_TIMER_MSEC_ON) new macro, set in milliseconds. (OSPF_HELLO_TIMER_ON) new macro to set hello timer according to whether fast_hello is set. * ospf_ism.c: Update all setting of the hello timer to use either OSPF_ISM_TIMER_MSEC_ON or OSPF_HELLO_TIMER_ON. The former is used when hello is to be sent immediately. * ospf_nsm.c: ditto * ospf_packet.c: (ospf_hello) hello-interval is not checked for mismatch if fast_hello is set. (ospf_read) Annoying nit, fix "no ospf_interface" to be debug rather than a warning, as it can be perfectly normal to receive packets when logical subnets are used. (ospf_make_hello) Set hello-interval to 0 if fast-hellos are configured. * ospf_vty.c: (ospf_auto_cost_reference_bandwidth) annoying nit, don't vty_out if this command is given, it gets tired quick. (show_ip_ospf_interface_sub) Print the hello-interval according to whether fast-hello is set or not. Print the extra 5 millisec characters from (ospf_timer_dump) if fast-hello is configured. (ospf_vty_dead_interval_set) new function, common to all forms of dead-interval command, to set dead-interval and fast-hello correctly. If a dead-interval is given, unset fast-hello, else if a hello-multiplier is set, set dead-interval to 1 and fast-hello to given multiplier. (ip_ospf_dead_interval_addr_cmd) use ospf_vty_dead_interval_set(). (ip_ospf_dead_interval_minimal_addr_cmd) ditto. (no_ip_ospf_dead_interval) Unset fast-hello. (no_ip_ospf_hello_interval) Bug-fix, unset of hello-interval should set it to OSPF_HELLO_INTERVAL_DEFAULT, not OSPF_ROUTER_DEAD_INTERVAL_DEFAULT. (config_write_interface) Write out fast-hello. (ospf_config_write) Write a comment about "auto-cost reference-bandwidth" having to be equal on all routers. Hopefully just as noticeable as old practice of writing to vty, but less annoying. (ospf_vty_if_init) install the two new dead-interval commands. * ospfd.h: Add defines for OSPF_ROUTER_DEAD_INTERVAL_MINIMAL and OSPF_FAST_HELLO_DEFAULT. --- ospfd/ospf_interface.h | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'ospfd/ospf_interface.h') diff --git a/ospfd/ospf_interface.h b/ospfd/ospf_interface.h index 2b129859..28d95d7e 100644 --- a/ospfd/ospf_interface.h +++ b/ospfd/ospf_interface.h @@ -55,7 +55,10 @@ struct ospf_if_params /* MTU mismatch check (see RFC2328, chap 10.6) */ DECLARE_IF_PARAM (u_char, mtu_ignore); - + + /* Fast-Hellos */ + DECLARE_IF_PARAM (u_char, fast_hello); + /* Authentication data. */ u_char auth_simple[OSPF_AUTH_SIMPLE_SIZE + 1]; /* Simple password. */ u_char auth_simple__config:1; -- cgit v1.2.3